viscosity breaking
英 [vɪˈskɒsəti ˈbreɪkɪŋ]
美 [vɪˈskɑːsəti ˈbreɪkɪŋ]
网络 减粘裂化
双语例句
- By way of conventional tests ( penetration, softening point, kinematic viscosity and Fraass breaking point) and dynamic mechanical analysis ( DMA), physical properties as well as rheological properties of styrene butadiene styrene polymer ( SBS) modified bitumens were studied.
用针入度、软化点、动粘度及脆点等常规试验方法与动态力学分析方法对Styrene-Butadiene-Styrene（苯乙烯-丁二烯-苯乙烯，简称SBS）聚合物改性沥青的物理特性及流变特性进行了研究。 - Evaluation results of the rheology property, viscosity breaking and hydration property, damage rate and anti-dilatation property of the fracturing fluid showed that the damage rates to induced fracture propping zone and to the matrix were 6.9% and 19.4% respectively.
通过评价该压裂液的流变性、破胶性能、伤害率和防膨性能得知，无残渣压裂液对裂缝支撑带的伤害率为6.9%，对储层基质的伤害率平均为19.4%； - A study on liquid backmixing characteristic in a viscosity breaking reactor
减粘反应塔液相返混特性的研究 - Under the conditions of reducing the polyester viscosity, raising the production load, by improving the after-spinning stretching ratio and stretching temperature, the quality indexes such as breaking tenacity etc were guaran-teed. The fiber drawing performance was improved.
在降低聚酯黏度、提升负荷的条件下，通过提高后纺拉伸倍率，拉伸温度等来保证断裂强度等品质指标，改善了纤维的拉伸性能。 - A novel water base gel breaker for fracturing fluid-EB-1 micro-capsule gel breaker is developed, to solve the difficulty of prophase viscosity reducing and gel breaking in the later period.
为解决压裂液的前期降粘与后期破胶困难的矛盾，研制出了一种新型的水基压裂液破胶剂&EB-1微胶囊破胶剂。 - Some affecting factors of the process for viscosity breaking were analysed by the principles of chemical reaction engineering.
运用化学反应工程理论分析了影响减粘裂化过程诸因素。 - In the numerical model a 'narrow slot'method is adopted to simulate mobile shore line and an eddy viscosity method to simulate wave breaking.
模型中通过“狭槽法”来处理波浪在岸线处的动边界条件，采用涡粘模型来模拟波浪破碎引起的能量耗散。 - Structure of depressurization injection allocator and viscosity-breaking injection allocation, as well as their primary surface test results, are introduced.
介绍了降压配注器和降黏配注器的结构以及初步地面试验结果。 - Thy results of conventional tests ( penetration, softening point, kinematical viscosity and Fraass breaking point) and those of dynamic mechanical analysis ( DMA) on Styrene Butadiene Styrene ( SBS) polymer modified bitumen are systematically compared.
将苯乙烯-丁二烯-苯乙烯（SBS）聚合物改性沥青用常规试验方法（针入度、软化点、动粘度及脆点）与动态力学分析方法所得到的试验结果进行比较研究。 - The maximum pressure drop for ball depressurization injection allocator is 2.4 MPa, and viscosity loss is less than 10%. The viscosity reduction ratio is rectifiable, and the peak value is 79% for viscosity-breaking injection allocator using electrochemistry catalytic viscosity reducing method.
投球式降压配注器最大压降达到2.4MPa，黏度损失小于10%，降黏配注器采用电化学催化降黏方式，最大降黏率79%，并且降黏率可以调整。 - To apply to the wave motions in nearshore region, the eddy viscosity method and slot method are respectively adapted to mimic the energy dissipation of wave breaking and moving shoreline boundary.
采用涡粘性方法处理波浪破碎、窄缝方法处理海岸动边界，使其适用于近岸波浪运动。 - We also discussed how spinning temperature influenced spinning compact, melt viscosity, spinnability, breaking strength.
探讨了纺丝温度对纺丝组件、熔体粘度、可纺性，断裂强度的影响。